简体中文界面。帖子、指南及政策正文保留原文；未对原文作自动翻译。

应用与集成

机床上下料、焊接、码垛及末端执行器。

发起讨论

3,712个讨论

A carton palletising project: Which drawings would connect carton support with gripper access?

LucyBennett0741 · 33 分 · 应用与集成 · 2026年8月2日

3条回复 M

Which drawings would connect carton support with gripper access? (Fairino FR10, palletising sealed product cartons)

MayaBrown0910 · 2 分 · 应用与集成 · 2026年8月2日

1条回复 R

Fairino FR5 pallet plan: support and tool access need the same review

RebeccaBrooks0865 · 22 分 · 应用与集成 · 2026年8月2日

13条回复 K

Before we add restraint to a fixture we don't fully understand - defining dimensional control for bracket welding

KaiChen1150 · 18 分 · 应用与集成 · 2026年8月2日

14条回复 A

What should I ask after an unconfirmed gripper-kit substitution? (Fairino FR5, placing small plastic samples in trays)

AmaraAbbott0078 · 15 分 · 应用与集成 · 2026年8月1日

1条回复 M

Our placing small plastic samples in trays tooling changed between the trial and delivery (Fairino FR5)

MayaArcher0388 · 20 分 · 应用与集成 · 2026年8月1日

10条回复 O

The layer pattern fits, but some cartons sit over gaps

OscarChen1141 · 7 分 · 应用与集成 · 2026年8月1日

0条回复 D

A compact fixture loading station: What should I report about this incomplete parts tray unloading improvement?

DanielAli0217 · 32 分 · 应用与集成 · 2026年8月1日

14条回复 O

What should count as dimensional acceptance after welding? (Fairino FR10)

OmarBarnes0578 · 7 分 · 应用与集成 · 2026年8月1日

0条回复 I

Do we need more than edge detection after reconnect? - part acceptance reporting

IsaacBrown0955 · 14 分 · 应用与集成 · 2026年8月1日

0条回复 C

应用与集成

A carton palletising project: Which drawings would connect carton support with gripper access?

Which drawings would connect carton support with gripper access? (Fairino FR10, palletising sealed product cartons)

Fairino FR5 pallet plan: support and tool access need the same review

Before we add restraint to a fixture we don't fully understand - defining dimensional control for bracket welding

What should I ask after an unconfirmed gripper-kit substitution? (Fairino FR5, placing small plastic samples in trays)

Our placing small plastic samples in trays tooling changed between the trial and delivery (Fairino FR5)

The layer pattern fits, but some cartons sit over gaps

A compact fixture loading station: What should I report about this incomplete parts tray unloading improvement?

What should count as dimensional acceptance after welding? (Fairino FR10)

Do we need more than edge detection after reconnect? - part acceptance reporting

Which bracket condition do our old UR5e planning records actually measure?

A sealed stainless panel is not yet a single delivered panel

Can I stop this FR5 pouch trial even though the transfer works?

Where do the turned dispatch cartons bear in our UR5e pattern?

Our 98-plate batch is nearly done only if repeat inspections are new plates

Does the delivered UR5e adapter preserve the shell trial we approved?

The panel seals on the bench, but I need it delivered singly from a stack

Working bag transfer, growing preparation bill

Different blank projections, no blank dimensions on our sheet

Which support view should accompany the occupied FR10 release sequence?