Latest discussions

Questions, experiences, and practical advice from the community.

Start a discussion

12,154discussions

Should I accept a different kit without seeing it handle our samples? - loading lightweight inspection pieces

KaiAli0193 · 25 points · Applications & integration · 10 May 2026

6replies R

Our example images keep turning shiny patches into defects - planning camera inspection of reflective parts

ReeceAbbott0036 · 5 points · Programming & support · 10 May 2026

1replies D

Is alternating the layers actually right for our cartons? - palletising sealed product cartons

DavidBarnes0606 · 7 points · Applications & integration · 10 May 2026

20replies Y

A robotic welding project review: Which old measurements can actually guide our fixture review?

YasminAllen0267 · 23 points · Applications & integration · 10 May 2026

10replies K

Is alternating the layers actually right for our cartons? (Fairino FR5)

KaiArcher0367 · 12 points · Applications & integration · 10 May 2026

6replies I

Universal Robots UR5e: Getting consistent inspection evidence before commissioning

IsabelBell0648 · 27 points · Programming & support · 10 May 2026

21replies L

Universal Robots UR5e: Seller calls the substituted kit equivalent; how do I check that?

LouisAli0224 · 28 points · Applications & integration · 10 May 2026

0replies H

I cannot choose our UR5e collar pads while the finish check changes with the viewer

AishaAli0257 · 7 points · Buying advice · 10 May 2026

1replies I

I cannot use the UR5e faceplate comparison while its labels lose the area names

ImranBrooks0827 · 6 points · Programming & support · 10 May 2026

7replies R

How do I get our missing FR10 controller crate traced separately from the arm?

RachelBrooks0870 · 26 points · Buying robots from China · 10 May 2026

6replies E

Our FR10 blank clears the mill sketch because nothing is holding it

EstherBurke · 33 points · Fairino robots · 10 May 2026

15replies P

The faster puck demo starts with somebody else's lovely tray

PriyaChan1090 · 17 points · Buying advice · 10 May 2026

7replies R

A small finished-parts production cell: What counts as a confirmed defect on a reflective surface?

RosaBennett0727 · 32 points · Programming & support · 10 May 2026

10replies

Latest discussions

Should I accept a different kit without seeing it handle our samples? - loading lightweight inspection pieces

Our example images keep turning shiny patches into defects - planning camera inspection of reflective parts

Is alternating the layers actually right for our cartons? - palletising sealed product cartons

A robotic welding project review: Which old measurements can actually guide our fixture review?

Is alternating the layers actually right for our cartons? (Fairino FR5)

Universal Robots UR5e: Getting consistent inspection evidence before commissioning

Universal Robots UR5e: Seller calls the substituted kit equivalent; how do I check that?

How do I make our FR5 old-completion test fail in the same order every time?

Our FR5 has two freight references but no warehouse confirmation

UR5e reporting test passes with the read removed

I cannot choose the FR5 cap proposal from two different starting trays

our fr5 layer section puts a component-case rail over a finger gap

UR5e packing proposal with training priced and changeover left blank

Why does our FR5 interface call a received request an available loading area?

I cannot choose our UR5e collar pads while the finish check changes with the viewer

I cannot use the UR5e faceplate comparison while its labels lose the area names

How do I get our missing FR10 controller crate traced separately from the arm?

Our FR10 blank clears the mill sketch because nothing is holding it

The faster puck demo starts with somebody else's lovely tray

A small finished-parts production cell: What counts as a confirmed defect on a reflective surface?